LEVRUS Load Module - NM-50kW-380V-3-K (50 kW)
Composition and characteristics of the load equipment NM-50kW-380 V-3-K | |
Equipment name | Load module NM-50kW-380 V-3-K |
Power | 50 kW |
Rated power of the steps | 5 x 10 kW; The steps can be increased or decreased smoothly or abruptly, and power can be switched on both sequentially (for example, adding 10/30/50 kW) and set immediately up to 50 kW and reduced immediately to 10 kW — depending on the requirements of the test procedure. |
Electrical load type | Active-resistive load |
Power circuit current type | Three-phase alternating current with a frequency of 50 Hz |
Rated voltage | ~400 V |
Power factor, cos (ϕ) | 0.99 |
Phase connection type | Star |
Operating mode | Continuous |
Ambient air temperature during operation of the load module | -25...+35 °C |
Emergency protection | Full protection: -overheating protection; -fan failure protection; -air flow protection (AFP) and RCD; -short-circuit protection; -emergency stop button. |
Forced air cooling | Three-phase axial fan powered from the source under load. |
Cooling air flow direction | Horizontal |
Control system | Built-in control panel. The control cabinet panel is intended for manual control of the load module and indication of operating and emergency modes. |
Recording of electrical operating parameters | Digital three-phase multimeter SATEC or analogue |
Protection rating of the main distribution board / control panel | IP 54 |
Insulation resistance | In accordance with the requirements of the technical specifications and the Electrical Installation Code. |
Insulation class | 1 kV (1000 V) |
Resistive elements | Tubular heaters, nichrome (NiCr 80/20), finned (steel with ceramic insulators), Russia. |
Circuit breakers | Contactors manufactured by IEK or analogue; other brands by agreement, with a corresponding change in cost. |
Noise level outside the container, no more than | 80 dBA |
Painting | Powder coating, RAL 5017 or in accordance with the technical specification |
Earthing of the load module | Two terminals (M10 threaded hole) on the outside of the load module enclosure |
Climatic design / Operation | UHL1. Operation outdoors is possible. All-weather enclosure, enclosure protection rating — IP 54 (with 4 bolts). |
Transportation | Resistance to transportation by land transport. |
Overall dimensions, no more than | Length 850 mm / Width 1000 mm / Height 1000 mm |
Weight, no more than | 170 kg |
Documentation | Full set of documents in Russian, including the operation manual, electrical connection diagram, certificate of conformity, load module data sheet |
Maintainability | Bolted modular construction, fully maintainable |
Maintenance | No special maintenance required. |
Designated service life | At least 12 years subject to compliance with storage and operating conditions |
Design of load module NM-50kW-380 V-3-K
The 50 kW, 400 V load module consists of a single load unit in a metal enclosure on a frame, on a chassis; the control panel is mounted inside the housing. The load complex enclosure is made of St08SS sheet steel not less than 1.5 mm thick.
The LR-50 load module in its housing and the control panel will comply with the requirements set out in your specification:
metal housing on a frame for indoor installation with removable and hinged panels for easy access inside the module, with protection degree IP 54 and control panel protection degree — IP 54
resistive load element bank
control and monitoring cabinet with instrument panel
switching and connection unit
terminal block for connecting power sources
axial fan
The NM-50kW-380 V-3-K load module will be supplied complete with a certificate, passport and operation manual.
* A long service life is only possible if the correct operating conditions described in the instructions are observed.
The 50 kW load module is supplied fully assembled and completely ready for further operation; it requires no additional on-site installation (other than connecting the cable to the power source under load and to the earthing circuit).




