From energy audit and design to on-site service: how LEVRUS LLC delivered energy independence for a country house in the village of Popovo, Chekhov District, Moscow Oblast.
Comfortable living in a modern country house is impossible without a stable power supply. Grid interruptions are not just a temporary loss of lighting; they put heating, water supply, security systems and food storage at risk. The solution was a full-cycle package from LEVRUS LLC: energy audit, design, equipment selection, installation, automation and after-sales support.
Design: the foundation of reliability
The first and key step after the site audit was the design of the future system. LEVRUS LLC specialists did not simply offer to buy a generator; they carried out a comprehensive analysis:
- Load calculations: the total and peak power of all loads in the house was determined — boiler, pumps, refrigeration equipment, ventilation system, lighting, etc.
- Configuration choice: based on the calculations, a decision was made to provide a three-phase 10 kW power supply system, taking into account current needs and possible future load growth.
- Connection diagram design: the company’s engineers produced a complete electrical schematic for integrating the standby source into the existing house network, identified the best location for the diesel genset and the automatic control cabinet, and routed cable lines in accordance with PUE requirements.
- Equipment selection: based on the project, a package was assembled where each component optimally complements the others in terms of power, interfaces and operating logic.
This approach ensured that the completed system would be not a collection of separate devices but a single, balanced and safe engineering package.
Technical core of the project: an automated diesel power plant
At the heart of the installed system is a ESY 10/230 diesel genset in a sound-attenuated enclosure with second-degree automation. This is a ready-made solution for year-round outdoor operation.
Key technical specifications of the ESY 10/230 diesel genset:
- Rated power: 10 kW / 12.5 kVA (three-phase, 400 V)
- Engine: Yanmar 3TNV88-GGE (Japan). 3-cylinder, 1.642 L. Direct injection.
- Fuel consumption: ~3.1–3.3 l/h at 100% load, ~2.0–2.2 l/h at 50% load.
- Alternator: Leroy Somer TAL-A40-C-S (France). Voltage stability ±1%.
- Control panel: DSE 6120 with full parameter monitoring.
- Tank: 50 litres. Coolant pre-heater as standard.
- Noise level: ≤ 65 dB(A) at 7 metres.
The choice of components (Yanmar + Leroy Somer + DSE) delivered an optimal balance of reliability, fuel economy and power quality.
Automation: an automatic transfer switch for seamless changeover
As specified in the project, a SHAUR-220/65-1S/1G automatic transfer switch cabinet (SHAUR) was integrated for power management.
Operating principle:
- The cabinet continuously monitors the external mains voltage.
- When the mains fails, the system sends a start command to the diesel genset.
- Once the genset reaches operating mode, the reversing power contactor KM-103 (65 A) automatically carries out an off-load transfer of the house load from the mains to the genset.
- When the mains is restored, the system transfers the load back in the reverse sequence and then shuts down the diesel genset.
Key feature: the ATS has an IP40 protection rating and a current margin (65 A), and installation was carried out strictly in accordance with the project documentation.
Remote monitoring: 24/7 peace of mind for the owner
A GSM remote monitoring module was included in the project from the outset.
What it gives the client:
- Instant SMS alerts to a phone when the mains fails, the generator starts or stops, fuel level is low or a fault occurs.
- Remote diagnostics: check voltage, current, running hours and other parameters from anywhere.
- Maintenance planning: fuel level monitoring for timely refuelling.
This turns the standby power system into an active and predictable element of a smart home.
Turnkey project delivery
LEVRUS acted as the main contractor and carried out all works:
- Installation and commissioning: site base preparation, cable routing, installation of the diesel genset and the SHAUR cabinet, connection and comprehensive testing. All works were completed with the signing of the Commissioning Certificate.
- Service support: for long-term reliability, the client was offered an Annual Service Contract covering scheduled maintenance in line with Yanmar regulations, emergency call-outs and ongoing support.
The project in the village of Popovo clearly demonstrates the advantage of a comprehensive engineering approach over simply selling equipment. LEVRUS acted as a single point of responsibility: designer, integrator and service partner.
From accurate load calculations and selection of economical equipment with proven characteristics to the introduction of smart automation and remote monitoring, every stage was aimed at one goal: providing the client with absolute energy independence and guaranteed power supply that requires no personal involvement.


