The SW1000L online UPS with 55 Ah batteries installed in the BS-36-1W battery rack is capable of providing autonomous operation of critical loads with a capacity of up to 1000 VA/900 W for 1 h 15 min (at 80% load). The autonomous operation time at other UPS load levels is presented on the Autonomous operation tab. Examples of loads include:
- gas boiler and circulation pump;
- water supply and water treatment system;
- television and audio equipment;
- personal computer and router.
In addition, the power supply provides protection of the connected equipment against voltage fluctuations.
Thanks to the improved power factor corrector operating algorithm, the SW1000L works efficiently in conjunction with a generator.
The SW1000L UPS with 55 Ah batteries operates on the basis of double-conversion technology, which allows the device to:
- stabilise the voltage with high accuracy (±2%) over the range (90-295 V) without switching to batteries;
- instantly and seamlessly switch the load power to the battery when the voltage fails or goes outside the above range;
- to supply electrical appliances with a voltage with an ideal sinusoidal waveform.
The power supply is equipped with a cooling system based on a low-noise fan.
Installation and connection
The UPS is mounted on the wall using a special bracket. The battery rack is placed on the floor.
Batteries are installed in the rack strictly in accordance with the operating instructions. It is important that the rack circuit breaker is in the OFF position and its cable is disconnected from the UPS.
The UPS is connected to the mains via a cord with a Schuko plug. The rack with the installed battery is connected to the already switched-on power supply via a TD50A-TD50A cable. The load is connected to the UPS last.
All components for installing and connecting the equipment are included in the scope of delivery.
Battery charging
The batteries in the battery rack are charged by the charger built into the UPS with a current of 5 A.
The power supply features modern technologies for reducing charging time and extending battery life (intelligent charging and battery charge temperature compensation), algorithms for disconnecting the battery at 80-85% discharge (protection against deep discharge), user notifications about battery wear and prediction of autonomy time at the current load.
Protection
The SW1000L has electronic protection against:
- short circuit:
- sustained output overload;
- internal overheating.
The UPS is able to automatically restore its operation after the cause of the electronic protection tripping has been eliminated.
The device is also equipped with protection against surge voltages and mains interference, as well as emergency protection against malfunctions (when activated, the load is transferred without interruption via bypass to the mains or disconnected).
Control panel
The UPS operation is monitored and its operating parameters configured on the control panel with an LCD display, which includes four control buttons and five LED indicators:
- "Status" – device operating mode and occurrence of alarms;
- "Mains" – input mains status;
- "Bypass" – electronic bypass/ECO mode;
- "Inverter" – operation from the inverter;
- "Battery" – battery status.
Types of information on the LCD display:
- input and output voltage values;
- UPS load percentage;
- battery voltage values and their status;
- active and apparent load power;
- alarms with indication of their causes.
The UPS control panel is also used to configure various device operating parameters and to start three types of battery test:
- for 10 seconds (the UPS powers the load from the battery for 10 seconds);
- for a specified time (the UPS powers the load from the battery for a specified time);
- to full discharge (the UPS powers the load from the battery until it is fully discharged, measuring the battery capacity and calibrating it).
Tests can be started and configured via the System menu, UPS Command item.
Monitoring tools
A card can be installed in the UPS to monitor the device's operation remotely over a local network or via the internet. Three models of such cards are available with the following interfaces:
- RS-232;
- USB or mini-USB;
- "dry" contacts;
- Ethernet (protocols: Web/SNMP/NTP/Modbus TCP/SHTYL).
The power supply is monitored via a web browser or the Shtyl Device Manager software. Please note that the expansion board is purchased separately.
All SHTYL manufacturer equipment offers an excellent price/quality ratio compared with similar products from foreign vendors on the Russian power supply systems market.
- Advantages





