The SW1000L online UPS with the BM-36-18 battery module, in which 6 batteries with a total capacity of 18 Ah are installed, will provide backup power for 20 min (at 80% load) to electrical equipment with a capacity of 1000 VA / 900 W. The autonomous operation time at other UPS load levels is presented on the Autonomous operation tab. Examples of loads are:
- gas boilers and other heating equipment;
- water supply and water treatment systems;
- security alarm and video surveillance systems;
- computer and multimedia equipment;
- low-power household appliances.
The UPS will also protect equipment from voltage surges and electrical interference. Thanks to the improved power factor corrector operating algorithm, the power supply interacts fully with generators.
The operation of the SW1000L UPS is based on double energy conversion technology, which allows the device to:
- correct the voltage with high accuracy (±2%) over the range (90-295 V) without switching to battery;
- instantly transfer the load power supply to the battery when the power fails or the voltage goes outside the operating range;
- to supply the load with a voltage of ideal sinusoidal waveform.
The power supply is cooled by a low-noise fan with adaptive speed control.
Installation and connection
The SW1000L UPS and the BM-36-18 battery module are mounted on a flat vertical surface using special brackets.
For connection to the UPS, the battery module has a TD50A "Anderson" connector. The load is connected to the UPS last.
All components intended for installing and connecting the devices are included in the scope of delivery.
Battery charging
The batteries of the battery module are charged by the charger built into the UPS with a current of 5 A.
The UPS employs modern technologies to reduce charging time and extend battery service life (intelligent charging and battery charge temperature compensation), algorithms for disconnecting the battery at 80-85% discharge (protection against deep discharge), notifying the user of battery wear and predicting autonomy time at the current load.
Protection
The SW1000L is equipped with electronic protection against:
- short circuit;
- sustained output overload;
- internal overheating.
The UPS supports automatic restart after the cause of the protection trip has been eliminated.
In addition, the device features:
- with surge and mains interference protection;
- emergency protection against operational faults (when they occur, the load is de-energised or switched to mains operation without interruption via the bypass).
Control panel
Configuration and monitoring of the main operating parameters of the product are performed using the control and indication panel. It includes an LCD display, four control buttons and five LED indicators:
- "Status" – device operating mode and occurrence of alarms;
- "Mains" – input mains status;
- "Bypass" – electronic bypass/ECO mode;
- "Inverter" – operation from the inverter;
- "Battery" – battery status.
Types of information on the LCD display:
- input and output voltage values;
- UPS load percentage;
- battery voltage values and their status;
- active and apparent load power;
- alarms with indication of their causes.
In addition, using the display and function keys on the control panel, the user can configure various device operating parameters and run three types of battery test:
- 10-second (the UPS supplies the load from the battery for 10 seconds);
- for a specified time (the UPS powers the load from the battery for a specified time);
- to full discharge (the UPS powers the load from the battery until it is fully discharged, measuring the battery capacity and calibrating it).
Tests can be started and configured via the System menu, UPS Command item.
Monitoring tools
The SW1000L allows the installation of an expansion card for local/remote monitoring of the device's operation. Three models of such cards are available with the following interfaces:
- RS-232;
- USB or mini-USB;
- "dry" contacts;
- Ethernet (protocols: Web/SNMP/NTP/Modbus TCP/SHTYL).
UPS monitoring with the installed board is possible via a web browser or the Shtyl Device Manager software. The board is an optional accessory and is not included in the standard scope of supply of the device.
SHTYL power supply systems are characterised by an excellent price/quality combination compared with similar products from foreign vendors on the Russian power supply systems market.
- Advantages





