The SW1000L online UPS with 100 Ah batteries installed in the BS-36-1W battery rack is intended for autonomous operation for 2.5 h (at 80% load) of connected loads with a capacity of up to 1000 VA / 900 W, for example:
- gas boiler and circulation pump;
- water supply and water treatment systems;
- video surveillance systems;
- video equipment;
- computer equipment.
Battery runtime at other UPS load levels is shown on the Battery operation tab.
The power supply is also capable of protecting the load from voltage fluctuations and electrical interference.
The UPS has an advanced power factor corrector algorithm that enables it to work efficiently in conjunction with a generator.
The SW1000L UPS with 100 Ah batteries is based on double-conversion technology, which achieves:
- voltage correction with high accuracy (±2%) over a wide range (90-295 V) without switching to battery mode;
- instant and seamless transition of the load power to the battery when the power fails or the voltage goes outside the above range;
- supplying consumers with voltage having a perfect sinusoidal waveform.
The UPS has a forced cooling system based on a low-noise fan.
Installation and connection
The UPS is mounted on a flat vertical surface using a bracket. The battery rack is placed on the floor.
Batteries are installed in the rack strictly in accordance with the operating instructions. It is important that the rack circuit breaker is in the OFF position and its cable is disconnected from the UPS.
The UPS is connected to the mains via a cord with a Schuko plug. The rack with the installed battery is connected to the already switched-on power supply via a TD50A-TD50A cable. The load is connected to the UPS last.
The scope of supply includes all components required for installation and connection of the devices.
Battery charging
The batteries in the battery rack are charged by the charger built into the UPS with a current of 5 A.
The power supply features modern technologies for reducing charging time and extending battery life (intelligent charging and battery charge temperature compensation), algorithms for disconnecting the battery at 80-85% discharge (protection against deep discharge), user notifications about battery wear and prediction of autonomy time at the current load.
Protection
The SW1000L has electronic protection against:
- short circuit;
- sustained output overload;
- internal overheating.
Automatic restoration of device operation is ensured after the cause of the protection tripping is eliminated.
The built-in varistor (2 kV (case-to-wire), 1 kV (wire-to-wire), response time – 50 µs) provides surge protection.
High-frequency filters protect the mains from interference in the 150 kHz - 30 MHz range and the load (from phase-to-neutral interference up to 2.5 kHz).
The UPS is also equipped with emergency protection against operating faults (when it is activated, the load is transferred without interruption via bypass to the mains or is disconnected).
Control panel
Configuration and monitoring of the operating parameters of the power supply are carried out on the control panel with an LCD display, which includes four control buttons and five LED indicators:
- "Status" – device operating mode and occurrence of alarms;
- "Mains" – input mains status;
- "Bypass" – electronic bypass/ECO mode;
- "Inverter" – operation from the inverter;
- "Battery" – battery status.
Types of information on the LCD display:
- input and output voltage values;
- UPS load percentage;
- battery voltage values and their status;
- active and apparent load power;
- alarms with indication of their causes.
The UPS control panel is also used to configure various device operating parameters and to start three types of battery test:
- for 10 seconds (the UPS powers the load from the battery for 10 seconds);
- for a specified time (the UPS powers the load from the battery for a specified time);
- to full discharge (the UPS powers the load from the battery until it is fully discharged, measuring the battery capacity and calibrating it).
Tests can be started and configured via the System menu, UPS Command item.
Monitoring tools
The UPS offers extensive capabilities for organising local/remote monitoring of its operation. For this, an expansion card is connected to the device. Depending on the model, it has the following interfaces:
- RS-232;
- USB or mini-USB;
- "dry" contacts;
- Ethernet (protocols: Web/SNMP/NTP/Modbus TCP/SHTYL).
The operation of the UPS with an installed card can be monitored directly in a web browser or in the Shtyl Device Manager software. The card is not included in the standard scope of supply and is purchased separately.
This equipment is characterised by an excellent price/quality ratio compared with similar products from foreign vendors on the Russian power supply systems market.
- Advantages




