The STR500SL-18 is a high-performance single-phase online UPS in a floor-standing/rack-mount design. The model will provide backup power supply and protection against voltage surges for critical equipment with a total capacity of up to 500 VA/400 W. Examples of the load may include:
- computer equipment;
- network equipment;
- security systems;
- emergency lighting;
- low-power household appliances.
The UPS functions efficiently in combination with household generators thanks to an improved power factor corrector algorithm.
The STR500SL-18 UPS is based on double-conversion technology, which provides:
- continuous voltage stabilisation in the 90-295 V range with high accuracy (±2%) without switching to the batteries;
- instant and seamless switching of appliance power to autonomous mode when the power fails;
- power supply to the load with an ideal sine wave voltage in any operating mode.
Installation and connection
The universal cabinet STR500SL-18 allows installation in two ways:
- into a 19-inch rack in a horizontal position (if the device is not placed on a shelf, it is recommended to additionally purchase a rack mounting kit);
- on the floor, a table or a shelving unit in a vertical position.
To connect the load, the UPS enclosure has a block of three "computer" C13 sockets. The device is connected to the mains via a 1.5 m mains cable with a Euro plug.
Battery operation
Battery operation of the load is provided by the built-in charger (current 5 A) and a battery block with four batteries with a total capacity of 18 Ah. At 100% load, the backup power supply to the connected electrical equipment will last 22 minutes (Battery runtime table).
Attention! The internal battery block is initially not connected to the UPS. This is done to prevent self-discharge of its battery. Before the first start-up of the device, the connector in the battery compartment must be connected. For more details, see the operation manual.
To extend battery runtime up to 2.5 h at 100% load, connection of up to 4 external battery modules BMRT-24-18 is provided for (Battery runtime table).
The STR500SL-18 uses modern technologies to reduce charging time and extend battery service life (intelligent charging and charge temperature compensation).
In addition, the model features special algorithms that allow:
- disconnect the battery at 80-85% discharge (protection against deep discharge);
- notify the user in advance of battery wear;
- accurately predict the autonomy time at the current load.
Control panel
For monitoring and configuring operating parameters, the STR500SL-18 UPS provides a control panel with an LCD display, function keys and five LED indicators:
- "Status" – indicates the device operating mode;
- "Mains" – indicates mains status;
- "Bypass" – indicates a switch to bypass/ECO mode;
- "Inverter" – indicates inverter operation;
- "Battery" – shows the battery status.
Information on the LCD display:
- input and output voltage values;
- UPS load percentage;
- battery voltage values and their status;
- active and apparent load power;
- alarms with indication of their causes.
Settings on the LCD display:
- start-up and operation mode;
- output voltage;
- nominal frequency when operating from the battery;
- bypass mode;
- on/off of the audible alarm;
- battery parameters (capacity, voltage, temperature compensation, etc.);
- battery test (time and period).
Three types of battery test are available:
- 10-second (load supply for 10 seconds);
- for a specified time (powering the load for a specified time);
- to full discharge (powering the load until the battery is fully discharged, with measurement of its residual capacity).
Cooling system
The device is equipped with a low-noise fan with automatic speed control, located on the rear panel.
Monitoring tools
A monitoring card can be installed in the STR500SL-18 to monitor its status and configure its parameters. The UPS supports several compatible monitoring cards with the following interfaces:
- RS-232 (Megatec protocol);
- RS-485 (Modbus RTU/SHTYL protocols);
- USB and mini-USB;
- Ethernet (protocols Web/SNMP/NTP/Modbus TCP/SHTYL);
- "dry" contacts;
- temperature sensor.
With the card installed, the UPS status can be monitored in a web browser or in the Shtyl Device Manager (SDM) software. To view the UPS status remotely in a web browser, the device must be connected to the internet via the Ethernet connector. An IC-SNMP/Web or IC-SNMP/mini-USB interface expansion card is required to set up such a connection.
The UPS parameters of the STR500SL-18 are edited via the control panel or the Settings menu of the Shtyl Device Manager software when the computer is locally connected to the UPS via the USB interface or the RS-232 interface.
Please note! The monitoring card is not included in the scope of supply and must be purchased separately.
Protection
The STR500SL-18 has electronic protection against:
- overload;
- short circuit;
- internal overheating.
Once the cause of the fault is eliminated, the device automatically restarts.
The built-in varistor (2 kV (case-to-wire), 1 kV (wire-to-wire), response time – 50 µs) provides surge protection.
High-frequency filters protect the mains from interference in the 150 kHz - 30 MHz range and the load (from phase-to-neutral interference up to 2.5 kHz).
The UPS is also equipped with protection against operating faults (if they occur, the load is either disconnected or transferred without interruption via bypass to the mains).
The STR500SL-18 online UPS offers an excellent price/quality ratio compared with similar products from foreign vendors on the Russian power supply systems market.
- Advantages







