‎+7 (499) 500-24-60
Moscow, Udaltsova St., 81, bldg 2, office 6
Single-phase UPS

SHTYL ST1103L online UPS (3 kVA / 2.7 kW)

  • Brand: Shtil
  • Product Code: ST1103L
  • Availability: Pre-order
52 910 ₽

The ST1103L online UPS ensures uninterrupted operation and stabilised power supply for a single-phase load with a power of 3 kVA/ 2.7 kW, for example:

  • heating systems and heating equipment;
  • computers and peripheral equipment;
  • household appliances, including equipment with electric motors;
  • retail and banking equipment;
  • lighting systems;
  • video surveillance and alarm systems.

Thanks to the improved power factor corrector operating algorithm, the ST1103L model functions excellently in conjunction with diesel generator sets.

ST1103L is an online UPS with double energy conversion, thanks to which the device allows:

  • stabilise the input voltage over a wide range (90-295 V) without switching to battery;
  • instantly and seamlessly switch the load power to the battery when the mains voltage fails;
  • supply the load with a perfect sinusoidal voltage with high stabilisation accuracy (±2%).

Installation and connection

The ST1103L is placed on the floor on any flat horizontal surface.

To power the load, the UPS rear panel provides the following connectors: two Euro sockets, three "computer" C13 sockets and one C19 socket. The device is connected to the mains via the C20 connector.

Battery operation

ST1103L is equipped with a charger (current 2 A) and a dedicated connector for connecting external batteries (up to 40 Ah), which provide the required load autonomy time (up to 30 minutes at 100% load) (Autonomy Time Table).

External batteries are installed using battery modules or racks.

The SW250SL uses modern technologies to reduce charging time and extend battery service life (intelligent charging and battery charge temperature compensation).

In addition, the model features special algorithms that allow:

  • disconnect the battery at 80-85% discharge (protection against deep discharge);
  • notify the user in advance of battery wear;
  • accurately predict the autonomy time at the current load.

Attention! If you purchase a UPS without an autonomous power solution from SHTYL Group (a battery module or a rack with batteries and a battery kit, see the Autonomous Operation tab), then to connect your own external batteries you will need to additionally purchase a TD50A battery cable (see the Accessories tab). It is not included in the basic UPS configuration!

Cooling system

The device is cooled by two low-noise fans with an adaptive operating mode.

Control panel

The main operating parameters of the ST1103L are monitored and configured using the control panel. It includes an LCD display, four function keys and five LED indicators:

  • "Status" – indicates the device operating mode;
  • "Mains" – indicates mains status;
  • "Bypass" – indicates a switch to bypass/ECO mode;
  • "Inverter" – indicates inverter operation;
  • "Battery" – shows the battery status.

The LCD display shows the following information:

  • input and output voltage values;
  • UPS load percentage;
  • battery voltage values and their status;
  • active and apparent load power;
  • alarms with indication of their causes.

The control panel allows three battery tests to be performed:

  • 10-second (the UPS supplies the load from the battery for 10 seconds);
  • for a specified time (the UPS powers the load from the battery for a specified time);
  • to full discharge (the UPS powers the load from the battery until it is fully discharged, measuring the residual capacity).

Tests are started via the System menu, UPS Command item.

Protection

The ST1103L is equipped with electronic multi-level protection against:

  • short circuit;
  • sustained output overload;
  • internal overheating.

The UPS recovers automatically once the cause of the electronic protection tripping has been eliminated.

In addition, the device is capable of protecting the load from mains interference and surge voltages (built-in varistor – 2 kV (case-to-wire), 1 kV (wire-to-wire), response – 50 µs). The UPS also has emergency protection against operational faults, when it triggers the load is either switched off or transferred to the mains via the built-in bypass without interruption.

Monitoring tools

Model ST1103L has special slots for installing monitoring cards with the following interfaces:

  • RS-232 (Megatec protocol);
  • RS-485 (Modbus RTU/SHTYL protocols);
  • USB and mini-USB;
  • Ethernet (protocols Web/SNMP/NTP/Modbus TCP/SHTYL);
  • "dry" contacts.

The UPS with an installed board is monitored in a web browser or in the Shtyl Device Manager (SDM) software.

The boards are not included in the standard scope of supply and are purchased separately.

Excellent price/quality ratio compared with similar products from foreign vendors on the Russian power supply systems market.

  • Advantages

General specifications
Apparent power, kVA 3
Active power, kW 2,7
Form factor floor-standing
Number of phases 1 to 1
Operating modes on-line, autonomous, bypass, ECO
Topology on-line (double conversion)
Country of manufacture Russia
Input characteristics
Generator compatibility yes
Input mains type single-phase three-wire (L, N, PE)
Input power factor 0,99
Limiting input voltage range, V 90-295
Maximum input current, A 19
Operating input voltage range, V 175-295 at 100% load, 155-295 at 75% load, 120-295 at 50% load
Power consumption in no-load mode, W 40
Rated input frequency, Hz 50
Rated input voltage, V 220
Soft start yes
Permissible input frequency range, Hz 45-65
Permissible deviation of the lower input voltage limit in ECO mode and for the electronic bypass, % -5, -10, -15, -20, -25 (default: -20)
Permissible deviation of the upper input voltage limit in ECO mode and for the electronic bypass, % +5, +10, +15, +20, +25 (default: +20)
Output characteristics
Crest factor 3:1
Maximum output current, A 13
Output power factor 0,9
Output voltage type single-phase
Rated output frequency, Hz when operating from the mains – matches the mains frequency; when operating from the battery – set by the user: 50/60 (default – 50)
Transfer time to battery mode from on-line mode, ms 0
Output voltage total harmonic distortion, % <2.5 with linear load, <4 with non-linear load
Rated AC output voltage, V 220
Output voltage waveform pure sine wave
Efficiency in online mode, % 95
Efficiency in battery mode, % 86
Output voltage stabilisation accuracy, % ±2
Output frequency stabilisation accuracy (when operating from battery), % ±0,2
Overload capacity (when operating in on-line mode or from batteries) 101-105% – no time limit, 105-130% – for 60 s, 130-150% – for 1 s, above 150% – for 0.2 s (followed by switching to bypass)
Efficiency in bypass or ECO mode, % 99
Transfer time to battery mode from ECO mode, ms 7
Overload capacity (when operating via bypass or in ECO mode) 200% for 40 s
Protection
Output overload electronic protection with auto-restart
Overheating electronic protection with auto-restart
Short circuit electronic protection with auto-restart
Protection against UPS failure electronic emergency protection
Protection against deep battery discharge yes
Electronic automatic bypass yes
Surge protection varistor (2 kV (case-to-wire), 1 kV (wire-to-wire), response – 50 µs)
Mains protection against high-frequency interference 150 kHz - 30 MHz
Load protection against mains interference (between phase and neutral) up to 2.5 kHz
Control panel and interfaces
Audible alarm battery mode (every 4 s), low battery voltage (every 2 s), battery disconnected/fully discharged/needs replacement (every 0,5 s), overload and UPS fault (continuous)
Ethernet option (monitoring card required)
LCD display display of system operating status and main input and output parameters
LED indication status, mains, bypass, inverter, batteries
RS-485 option (monitoring card required)
Indication type LCD display and LED indication
EPO two-contact screw terminal (terminal block), conductor cross-section: 0.08-1.2 mm².
"Dry" contacts option (monitoring card required)
mini-USB option (monitoring card required)
RS-232 option (monitoring card required)
Function keys control of the menu displayed on the LCD, UPS configuration
USB option (monitoring card required)
Connection
Input mains IEC-320-C20
Load (output sockets) IEC-320-C13 (3 pcs.), EURO F-type with grounding (2 pcs.), IEC-320-C19 (1 pc.)
Reliability and performance characteristics
Cooling type forced air cooling (fan)
Degree of protection against dust and moisture IP20
Installation indoor
Operating altitude, m up to 3000 m above sea level
Relative humidity, % from 0 to 80 (non-condensing)
Service life, years at least 10
Warranty period, months 24
Operating temperature range, °C from +5 to +40
Storage temperature range, °C from -40 to +40
Mechanical characteristics
Housing colour grey
Weight, kg 14
Overall dimensions HxWxD (unpacked), mm 346x210x443
Overall dimensions HxWxD (packed), mm 505×260×395
Batteries (battery packs)
Battery availability external (option)
Hot-swap of built-in batteries no
Battery runtime (at 80% UPS load) Depends on the external battery capacity
Rated battery voltage, V 96
Battery type sealed, maintenance-free, lead-acid
Battery management functionality residual capacity determination, tests (10-second, for a specified runtime, until full discharge), deep discharge protection, charge temperature compensation
Cold start yes
Rated charge current of the built-in charger, A 2

Write to us

We will reply to info@levrus.ru shortly