The ST1102L online UPS ensures uninterrupted operation and protection against mains voltage fluctuations for single-phase electrical appliances with a power of 2 kVA / 1.8 kW, for example:
- heating and warming equipment;
- personal computers and peripheral computer equipment;
- network equipment;
- household electrical appliances;
- banking equipment;
- retail and point-of-sale terminals;
- video surveillance and alarm systems.
Thanks to the improved power factor corrector operating algorithm, the ST1102L model functions excellently in conjunction with diesel generator sets.
The ST1102L is an online UPS with double conversion of electricity, thanks to which the device allows:
- stabilise the input voltage over a wide range (90-295 V) without switching to autonomous mode
- instantly and seamlessly switch the load power to the battery when the mains voltage fails
- supply the load with a perfect sinusoidal voltage with high stabilisation accuracy (±2%).
The device is cooled by two low-noise fans.
Installation and connection
The ST1102L is intended for floor installation. The UPS can be placed on any flat horizontal surface.
To power the load, the UPS rear panel provides the following connectors: two Euro sockets, three "computer" connectors (C13) and one C19 socket. The UPS is connected to the mains via the C20 connector.
Battery operation
The ST1102L has a built-in charger (4 A current) and a special connector for connecting external batteries. The maximum capacity of external batteries is 100 Ah (without an external charger) and 200 Ah (with an external charger), which will provide autonomous operation for 2 h or 5.5 h respectively (at 100% load) (Battery Runtime Table).
External batteries can be installed in battery modules or racks.
The UPS employs modern technologies to reduce charging time and extend battery service life (intelligent charging and battery charge temperature compensation).
Attention! If you purchase a UPS without an autonomous power solution from SHTYL Group (a battery module or a rack with batteries and a battery kit, see the Autonomous Operation tab), then to connect your own external batteries you will need to additionally purchase a TD50A battery cable (see the Accessories tab). It is not included in the basic UPS configuration!
In addition, the model features special algorithms that allow:
- disconnect the battery at 80-85% discharge (protection against deep discharge);
- notify the user in advance of battery wear;
- accurately predict the autonomy time at the current load.
Control panel
The main operating parameters of the product are monitored and configured using the control panel. It includes an LCD display, four function keys and five LED indicators:
- "Status" – indicates the device operating mode;
- "Mains" – indicates mains status;
- "Bypass" – indicates a switch to bypass/ECO mode;
- "Inverter" – indicates inverter operation;
- "Battery" – shows the battery status.
Information displayed on the LCD display:
- input and output voltage values;
- UPS load percentage;
- battery voltage values and their status;
- active and apparent load power;
- alarms with indication of their causes.
The control panel allows three battery tests to be performed:
- 10-second (the UPS supplies the load from the battery for 10 seconds);
- for a specified time (the UPS powers the load from the battery for a specified time);
- to full discharge (the UPS powers the load from the battery until it is fully discharged, measuring the residual capacity).
Tests are started via the System menu, UPS Command item.
Protection
The ST1102L UPS has a built-in modern electronic protection system against:
- output overload;
- short circuit;
- internal overheating.
Once the cause of the protection tripping has been eliminated, the device automatically resumes operation.
In addition, the UPS is equipped with protection against high-frequency mains interference and surge voltages, as well as operational faults (when they occur, the device disconnects the load or transfers its operation to the mains via bypass, maintaining uninterrupted power to the connected devices).
Monitoring tools
Model ST1102L supports local/remote operation monitoring. For this purpose, the rear panel of the device provides two slots for installing expansion boards with the following interfaces:
- RS-232 (Megatec protocol);
- RS-485 (Modbus RTU/SHTYL protocols);
- USB and mini-USB;
- Ethernet (protocols Web/SNMP/NTP/Modbus TCP/SHTYL);
- "dry" contacts.
The UPS with an installed board is monitored via a web browser or the Shtyl Device Manager (SDM) software. The boards are not included in the standard scope of supply and are purchased separately.
Excellent price/quality ratio compared with similar products from foreign vendors on the Russian power supply systems market.
- Advantages







