‎+7 (499) 500-24-60
Moscow, Udaltsova St., 81, bldg 2, office 6
Project solution UPS

SHTYL UPS ST1102SL (AT1)

  • Brand: Shtil
  • Product Code: ST1102SL-AT1
  • Availability: In stock

The single-phase UPS ST1102SL (SHTYL) AT1 is designed for use at particularly critical facilities (including railway infrastructure and metro facilities) to provide backup power and protect 2 kVA/1.8 kW equipment against voltage fluctuations and surges.

Due to the use of these UPS models at important facilities, a number of improvements have been made to them to increase fault tolerance.

In addition, unlike standard mass-produced devices, they have an extended warranty period of 3 years (36 months).

ST1102SL (Shtyl) AT1 is an online UPS with double conversion technology, thanks to which the device allows:

  • stabilise the input voltage over a wide range (90-295 V) with high accuracy (±2%) without switching to battery;
  • instantly and without interruption transfer the load supply to the battery when the mains voltage fails;
  • supply the load with a pure sine wave voltage both when operating from the mains and from the battery.

Installation and connection

ST1102SL (Shtyl) AT1 is installed on any flat horizontal surface on rubber feet.

To provide power to connected electrical appliances, the UPS rear panel has the following connectors: two Schuko sockets, three computer sockets (C13) and one C19 socket. The device is connected to the mains via a connector (C20).

Standalone operation

For autonomous operation of the load, the model has built-in batteries (9 Ah) and a charger (current 1 A). The batteries ensure operation of electrical appliances for 5 minutes (at 100% load). Additional battery modules can be connected to the UPS via the TD50A connector.

Protection

ST1102SL (Shtyl) AT1 is equipped with all the necessary types of electronic protection:

  • against short circuit;
  • against prolonged output overload;
  • against internal overheating.

The UPS is able to restore its operation automatically once the cause of the protection trip has been eliminated.

The device also has an input and output mains filter that protect the load from high-frequency interference. A built-in varistor (2 kV, 1/50 µs) provides surge protection.

In addition, the uninterruptible power supply has emergency protection against any fault. When it is triggered, the consumers are disconnected or their power is transferred to the mains without interruption via the built-in bypass.

Indication

To monitor UPS operation, it is equipped with an intuitive LED indicator panel that does not require additional study of the operating documentation to diagnose the device status.

The device has the following indicators:

  • "Status" – notifies of the device operating mode;
  • "Overheating" – notifies of device overheating;
  • "Mains" – notifies of the mains status;
  • “Bypass” – notifies of switching to bypass/ECO mode;
  • "Battery" – shows the battery status;
  • load level and battery discharge indicator.

Monitoring facilities

The status of ST1102SL (Shtyl) AT1 can be monitored both locally via the USB/RS-232 interfaces and remotely after installing an Ethernet adapter. These interfaces are located on monitoring cards, which are installed in a special connector on the rear panel of the device.

Operation of the UPS with an installed monitoring card is conveniently monitored on a PC via a web browser or the Shtyl Device Manager (SDM) program.

Please note that the cards are not included in the basic configuration and are purchased separately.

  • Specifications

General specifications
Apparent power, kVA 2
Active power, kW 1,8
Form factor floor-standing
Number of phases 1 to 1
Topology on-line (double conversion)
Country of manufacture Russia
Input characteristics
Generator compatibility yes
Input mains type single-phase three-wire (L, N, PE)
Input power factor 0,99
Limiting input voltage range, V 90-295
Maximum input current, A 13,5
Operating input voltage range, V 175-295 at 100% load, 155-295 at 75% load, 120-295 at 50% load
Rated input frequency, Hz 50
Rated input voltage, V 220
Soft start yes
Permissible input frequency range, Hz 45-55
Permissible deviation of the lower input voltage limit in ECO mode and for the electronic bypass, % -5, -10, -15, -20, -25 (default: -20)
Permissible deviation of the upper input voltage limit in ECO mode and for the electronic bypass, % +5, +10, +15, +20, +25 (default: +20)
Output characteristics
Crest factor 3:1
Maximum output current, A 9
Output power factor 0,9
Output voltage type single-phase
Rated output frequency, Hz when operating from the mains - matches the mains frequency; when operating from the battery (user-set) - 50/60
Transfer time to battery mode from on-line mode, ms 0
Output voltage total harmonic distortion, % <2.5 with linear load, <4 with non-linear load
Rated AC output voltage, V 220
Output voltage waveform pure sine wave
Efficiency in online mode, % 95
Efficiency in battery mode, % 86
Output voltage stabilisation accuracy, % ±2
Output frequency stabilisation accuracy (when operating from battery), % ±0,2
Overload capacity (when operating in on-line mode or from batteries) 105-130% - for 60 s, 130-150% - for 1 s, more than 150% - for 0.2 s followed by switching to bypass
Transfer time to battery mode from ECO mode, ms 7
Efficiency in mains operation mode, % 99
Control panel and interfaces
Audible alarm battery mode, low voltage of internal and/or external batteries, battery disconnected/fully discharged/needs replacement, overload and UPS fault
Ethernet option (monitoring card required)
EPO pluggable screw terminal block, wire cross-section: 0.08-1.2 mm².
"Dry" contacts option (monitoring card required)
mini-USB option (monitoring card required)
RS-232 option (monitoring card required)
USB option (monitoring card required)
LED display display of the system operating status, 3 control buttons and indicators: status, overload, overheating
Connection
Input mains IEC-320-C20
Load (output sockets) IEC-320-C13 (3 pcs), earthed EURO F-type (2 pcs), IEC-320-C19 (1 pc)
Reliability and performance characteristics
Degree of protection against dust and moisture IP20
Installation indoor
Operating altitude, m up to 3000 m above sea level
Relative humidity, % from 0 to 80 (non-condensing)
Service life, years at least 10
Warranty period, months 36
Operating temperature range, °C from +5 to +40
Storage temperature range, °C from -40 to +40
Mechanical characteristics
Housing colour grey
Weight, kg 28
Overall dimensions HxWxD (unpacked), mm 346x210x443
Batteries (battery packs)
Battery availability built-in and external (optional)
Hot-swap of built-in batteries no
Battery runtime at 100% (50%) UPS load, min 6 (18)
Internal battery capacity, Ah 9
Number of built-in 12 V batteries, pcs. 6
Rated battery voltage, V 72
Battery type sealed, maintenance-free, lead-acid
Battery service life, years up to 7 (depending on operating conditions)
Battery management functionality capacity calibration, tests (10-second, for a specified runtime, to full discharge), deep discharge protection, charge temperature compensation
Cold start yes
Built-in battery charge time, h no more than 8 (up to 90% capacity)

Write to us

We will reply to info@levrus.ru shortly